Just drive it for about a 100 miles and then tell us what happens. Your car may need to adapt to the new height

 

are the lights for traction and brake (in yellow) on???

 

did they do any interior work? The warning triangle just stays off? The button should not have stopped working because you had suspension work done.

 

U mentioned interior work??
Wat does this mean o have a crazy problem of my DSC not working and the ONLY code is the ZKE module for interior lights..???

 

ive had to do a 500 mile trip a couple days later and it still doesnt work.... i have no traction lights at all on, the dsc is on bc when it rains i like to have a little bit of fun, but its no fun when the traction is always on..... there wasnt any interior work done. after doing some research a wheel speed sensor may have been damaged so my next step will be checking them out

 

Check to make sure your DSC button is plugged in first. I had this happen one time and somehow it got unplugged. If it was your wheel speed sensors, I would think you would have the yellow traction lights on.

 

Check the fuse box. Last thing I thought to check when my button stopped working but the fuse was missing. Can't remember which one it is but the chart will tell you. I think mine fell out when I was replacing a blown one. Worth a shot! And could possibly save you some money.

Sent from my DROIDX using BimmerApp

 

bmw



Where is the fuse for the dsc button and the speaker button?

 

Have you tried spinning the tires and seeing if the traction light comes on?

 

got it workin, i checked the fuse, that was okay, so i went to see if it was actually plugged in and it was i unplugged it, turned the key to the 2 possition waited a couple seconds turned it off, plugged it back in and then turned the key again and viola it works again.... im stumped must be just havin her PMS of the month, either way now i can have some fun again.. cant wait to make my voyage to NY for christmas time hopefully there is a little bit of snow

thanks for all the suggestions everyone :thumbsup:

 

Where was it unplugged? I'm assuming at the switch on the interior? I'm having similiar issues and would like any help I can get.

Thanks,
Nic

 

Thanks for the reply, I shouldn't have any issues getting the trim off, I just wasn't sure if that was what he was talking about. I'll have to give it a try to see if that helps.

 

stop fully. then punch it. see if the light comes on when ur tires spin out. then try the buton again

 

It’s definitely not working. I've had quite a few opportunities to prove it this winter.

 

so my dsc switch is unplugged, but traction kicks in when i try getting sideways or spin the tires. i guess the system believes safety first even when the switch isnt present.

 

My buttons don't work either. I hate to also bring this topic back from the dead... But I really need help figuring out why my HK and DSC buttons dont work. I need to smog my car (California) to be able to register it, but they wont smog it unless they can turn off the DSC. And I only have like 4 days left! Ive tried the fuses and checking the switch... The fuses were good and there were only 2 switched on that bar. One long one with a lot of wires, and another smaller one. And the back of the button was a PITA to get to. Please help.

 

I hate to also bring this topic back from the dead... But I really need help figuring out why my HK and DSC buttons dont work. I need to smog my car (California) to be able to register it, but they wont smog it unless they can turn off the DSC. And I only have like 4 days left! Ive tried the fuses and checking the switch... The fuses were good and there were only 2 switched on that bar. One long one with a lot of wires, and another smaller one. And the back of the button was a PITA to get to. Please help

I HAVE THE EXACT SAME PROBLEM!?
Please help!!