E46 Fanatics Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-14 of 14 Results
  1. E46 General
    I need some testimonies after installing transgo pressure valve in ZF 5HP19 auto trans. I got an issue when braking to stop. I felt hard downshift (jolt) from 3 to 2 when moderate breaking, but when I am not pressing my brake pedal that much it seems to work fine. When I use manual mode to down...
  2. E46 General
    A couple months ago, I started feeling a rough shift (both in "D" and "SD") around 70-75 mph. In the past, I have gotten a "stall speed" issue when the car sits in drive. Did a fluid and filter change (not flush) with new sensors. Fast forward to yesterday. I'm on my way home, and I get an SES...
  3. E46 General
    After replacing the tc and oil pump, trans was working and driving perfectly until I went to get on the highway and went into failsafe, overrevved and cut the engine. Upon restart, no gears catching still with cog light on. Checked the trans fuse block and everything was good, throwing p0721...
  4. E46 General
    Hey guys. Just finished replacing my tc and oil pump in my ZF5hp19. Still need to fill fluid to correct level, but when I started the car I got the gear with the ! Trans failsafe with brake abs and nothing else, guessing those are on because it’s still in the air as well. Shifts through the...
  5. E46 General
    Just finished doing the oil pump and torque converter on my 01 330CI. Topped fluid off and had a communication issue due to pinched o2 wires which I’ll fix soon enough, but now having trouble when moving car into neutral and reverse the car moves forward. Anything would help lmao before I end up...
  6. E46 General
    My 330 developed a crazy trans leak out of the bell housing where you can see the sore converter, it gave me the torque converter code prior to failure, I was reading forums and came to the conclusion that obviously I need at least a pump seal Or the safer bet is probably replacing the whole...
  7. E46 General
    hallo guys I'm using an e46 325i with a zf5hp19 transmission. I just replaced all the seals and clutch matic using original ZF parts. I also replaced my speed output sensor with the original zf part. I feel if I use the transmission in the "D" position when I stop suddenly the shift from 2...
  8. E46 General
    Hello everyone! Recently I've purchased an 1998 328i sedan with the zf5hp19 transmission that goes into limp mode intermitently... It is totally random. In six months it did around 2 or 3 times. Simply turning off the car and restarting makes the limp mode go away. I went to find what was...
  9. E46 General
    Installed all new sensors and brand new wiring harness in the transmission after it threw a few different codes. (P1732 Gear Monitoring 4 @ Electrical Sub Program, & P0721 Output Speed Sensor) Fast forward to last night. I put new fluid in the transmission, but still had the P1732 code...
  10. E46 General
    Hello everyone. I replaced my ZF5 in my 2001 330i today. It was a used tranny that came with the TC with supposedly 130k from a car that had been wrecked. After a smooth RandR (my second time doing on an e46) I filled it up with pentosin and when I fired it up it started dumping fluid from...
  11. E46 General
    hi guys, i'm new in this group or website or ..., i don't know :D . i have a 330ci convertible with ZF5HP19 automatic transmission , and i'm about to tune it without changing my tranny to a manual or SMG one, so i'm not sure someone did this before or not, because i know always manual or smg...
  12. E46 General
    So I've decided to rebuild my trans because of a broken reverse drum, here are some photos. This is not intended as an diy guide. Posting to document the process taken. Any help is appreciated. Right now im working on getting the oil pump out. Thanks. Tools needed: Ratchet with a few...
  13. E46 General
    Greetings all! TL;DR - came to shop with no reverse, replaced the drum ONLY, now has several codes and goes into limp after trying for 3rd gear. Also replaced a rectangular section sealing ring with silicon because my boss and the customer have less knowledge than money they're willing to...
  14. E46 General
    Greetings all! TL;DR - came to shop with no reverse, replaced the drum ONLY, now has several codes and goes into limp after trying for 3rd gear. Also replaced a rectangular section sealing ring with silicon because my boss and the customer have less knowledge than money they're willing to...
1-14 of 14 Results
Top