E46 Fanatics Forum banner
  • Hey everyone! Enter your ride HERE to be a part of December's Ride of the Month Challenge!
bracket
1-13 of 13 Results
  1. E46 General
    I currently don't have a plate on the front of my car, but apparently you need one in New York. Anybody have any recommendations for retractable front license plate brackets? Can be mechanical or electronic, just something that hides the license plate for pictures, etc. Preferably don't want to...
  2. E46 General
    I am replacing three brake hoses (did the right front recently) but I find the new rear hoses does not fit snugly into the "Brake Pipe Bracket" that bolts onto the inside of the trailing arm. These are rear ATE brake hoses (331429, ATE: 24.5169-0458.3) and comes up as 343 011 65 174, which is...
  3. E46 General
    I have always noticed that one of the power steering hoses hangs wayy too low when the front splash guard is off. Since I always leave it on apart from when I am working under the car, I have never given it a second thought. Upon closer inspection, I noticed that there seems to be evidence of...
  4. E46 General
    So I currently have an issue whereby Iv broken the expansion tank mount where the ET top hangar is meant to hang on to. Could this be the reason why I can't seem to get the Expansion tank to seat no matter how hard I push down ?
  5. Forced Induction
    I have a E46 328i that im supercharging with a Vortech V1. Does anyone know where i can get a bracket to fit my car with all necessary hardware.
  6. E46 General
    Hey guys, I have auto leveling xenon headlights and ever since I replaced my control arms years ago, my headlights have never worked the same since. I do not have the little up/down test that I used to when I started up the car. I was never able to properly connect the sensor arm to the...
  7. E46 General
    Hi, my name is Ron. This is my first time posting to the forums. My car is a 2002 325Xi. I just bought it last week - it drives great! It has 100k miles on it and I paid $3900. I think I did OK, even though it has been in some kind of 'fender bender' and thats why it was cheap. I don't mind...
  8. E46 General
    I've a 2003 325i Sport with manual transmission. The front part of my exhaust configuration consists of a twin pipe that bolts directly to the manifold twin pipes and is held in place by bracket that mounts onto the transmission housing. This bracket is connected to the exhaust via a single bolt...
  9. E46 General
    Im looking to purchase a tow hook mounted license plate holder but cant figure out if i should order the coupe or m3 one. I have a 330ci but have an M3 replica bumper installed, anyone running one on a rep bumper? IDK if its different diameter tow hook, location of the hook different on M3, or...
  10. E46 General
    Ok so my body shop is installing a new mtech II kit but when they were going to put the rear they called me and said it doesnt match up. They wanted to aske me what they should do or if I know of any new brackets i can put in place of the stock ones to make the bumper fit properly. (Attached are...
  11. E46 General
    Mtech II Brackets/Air Ducts on Facelift ...Which Brackets?Vendor? Ok so I need to buy the Mtech II front and rear bumpers, My car is in the shop waiting. Ive been searching the forum all over for this info and found some but i just want to clarify it .... If I buy the Mtech II kit for my...
  12. E46 M3
    Just spent the last 6hrs trying to install these brackets to fix the rear bumper sag with no luck! Attached are some photos (sorry for the quality) but I have no idea where to place them or how to install them once I remove the inner fender guard. Can anyone help? This is very frustrating and...
  13. E46 General
    Hey guys, So I went to the bodyshop today to finally pick up my facelift coupe that is getting an extreme make over with M3 rep front + MVR CF lip + GTR Sides + SRS rear, but... :excited: Hiccup#1 They were unable to finish it due to the rear bumper not fitting properly!!! :banghead: I have...
1-13 of 13 Results
Top