E46 Fanatics Forum banner
  • Hey everyone! Enter your ride HERE to be a part of December's Ride of the Month Challenge!
bolt
1-12 of 12 Results
  1. Motorsports, Track
    Wondering if anyone can help link me or just tell me what measurement bolt I would need for my tow strap. I want one long enough so I don’t have to remove my bumper to do it. Just like shown in this picture. appreciate any replies. e46 320cd 2003
  2. E46 Convertible
    Hi, I've looked on realoem (330CI 2002 convertible) and cannot find the bolt part number that attaches the foremost driver side hydraulic actuator to the convertible frame right by the hinge point by the drivers head! Does anyone happen to have this? Thanks, Bruce
  3. E46 General
    I replaced the trailing arm bushings on my 2002 330i today and I'm finished except for one bolt that I suspect that I've cross threaded. It's one of the three bolts on one side that hold the bracket to the body. The bolt turns easily and then binds completely with at least a 1/2-inch to go...
  4. E46 General
    HELLO ALL....I've been trying to replace my oil filter housing gasket this past weekend and I've ran into a big problem... the damn alternator bolt :censor: I've removed all the bolts except for the 16mm long bolt on the bottom. I can turn the bolt with a breaker all day (I know it's turning)...
  5. E46 General
    Hi everyone... So, in the latest chapter of my oil pan repair fiasco, I sheared the very last fastener I was torquing in place :facepalm:. Not sure how that's possible with a torque wrench set to a whopping 10 Nm, but it happened. Anyway, for a variety of reasons, I can't wait till Tuesday to...
  6. E46 General
    Hey everyone, My e46 is a 2001 with 110k and I'm in the process of changing my ZF 5HP19 ATF. I was able to get the fill plug off so I proceeded to drain my transmission fluid which was very dirty. I then start unscrewing the 20 bolts that border the transmission pan and I came across one bolt...
  7. Suspension, Brakes
    I was doing the RTABS with my friend, when my trailing arm wouldnt drop low enough to make the clearance to press them out, I figured out that my aftermarket sway bar was too thick and hitting the axles, no big deal, I just had to remove the sway bar. But anyways, my friend thought it would be...
  8. E46 General
    I started changing the belts and pulleys on my 2003 330i (88,000 mi, 60k on the belts). The bolt for the idler pulley felt cross threaded and was very difficult to remove. For better or for worse, I muscled it off and put on the new idler. The bolt was difficult to put back as well, so i took...
  9. E46 General
    Need some advice on how to loosen my oil pan bolt. Seems that last time I changed my oil, I tightened it a bit too much and now im unable to loosen it. My dad told me that the heat and cold can cause the bolt to expand and tighten in even more. Any suggestions to loosen it up? Maybe heating it up?
  10. E46 General
    So I am trying to do the oil filter housing gasket and i am trying to remove the alternator... problem is the top bolt that goes through the pulley is stuck on like a b!tc4... i tried and tried to get it to budge for the past 45 minutes and its not giving away. Ive tried my socket wrench, my...
  11. E46 General
    Ok, so I want to order these 12.5 mm spacers http://www.turnermotorsport.com/html/detail.asp?PRODUCT_ID=TWH9905013 Now I've searched the forum about bolt length and I found some posts say 35mm for 12mm spacer, some 40mm. Can you tell me guys what bolt length I need for 12mm spacer? Thx! PS...
  12. E46 M3
    Anyone know what the Lug/Bolt Pattern is for the E46 M3 2002 model to be exact, i'm looking online for a set of track wheels and tires, and can't seem to figure out what the bolt pattern is. Thanks
1-12 of 12 Results
Top